Gravel & Crushed Stone Calculator: m³ or Cubic Yards to Tonnes
Work out how much crushed stone, sand, sand-gravel mix, expanded clay, topsoil or gravel you need for a path, pad or base — in cubic metres and tonnes or in cubic yards and US tons — or convert volume to weight and back. Bulk materials only; concrete mixes are out of scope.
Quantity
Allowance & density
How this is calculated
Volume is area (length × width, or the area you enter) times layer thickness. An allowance for compaction and losses is added on top, because loose material settles when tamped: 25% for crushed stone, gravel and sand-gravel mix, following the lower bound of Russian road-construction rules (SP 78.13330) and the Soyuzdornii guide for crushed-stone bases; 12% for sand, from supplier practice; none for expanded clay and topsoil. That order volume converts to weight using the bulk (loose) density of the chosen material — granite crushed stone about 1.37–1.38 t/m³, sand about 1.5, sand-gravel mix about 1.7, expanded clay about 0.45, topsoil about 1.2. Densities are typical values from producer passports and supplier tables. In US units the same densities are shown in short tons per cubic yard (1 ton/yd³ = 1186.553 kg/m³), and volume uses 27 cubic feet per cubic yard; the unit definitions follow NIST Handbook 44. Bag count is total weight divided by the bag weight, rounded up.
Worked example
A 10 × 1 m path, 15 cm layer of 20–40 mm crushed stone. Volume in place: 10 × 1 × 0.15 = 1.5 m³. With a 25% compaction allowance: 1.5 × 1.25 = 1.88 m³. Weight: 1.88 × 1.38 ≈ 2.59 t — 65 bags of 40 kg or 52 bags of 50 kg.
Before you order
- Order by the density on your supplier's passport or ticket if you have it — type it into the density field. Bulk density varies by quarry, moisture and grading; the defaults are typical market values, not your load.
- Tamped stone and sand take up less space than loose material, so the calculator adds an allowance: 25% for crushed stone, gravel and sand-gravel mix (the lower bound of road-base guidance for roller-compacted stone), 12% for sand, none for expanded clay and topsoil. Hand-tamped garden paths often need less — the field is editable.
- Building up several layers (sand bedding + crushed stone)? Run the calculator once per layer — each material has its own density and compaction allowance.
- Suppliers sell by volume (m³ or cubic yards) or by weight (tonnes or tons) — check which one your quote uses before comparing prices. In US units, "ton" here means the 2000 lb short ton.
Common questions
How many tonnes are in a cubic metre of crushed stone?
Granite crushed stone weighs about 1.36–1.40 tonnes per loose cubic metre depending on fraction (5–20, 20–40 or 40–70 mm), so one tonne is roughly 0.72–0.73 m³. In US units that is about 1.15–1.18 tons per cubic yard. Your supplier's ticket gives the exact figure for their material.
How much compaction allowance should I add?
For coarse crushed stone and sand-gravel mixes compacted by roller, road-construction guidance gives 1.25–1.3× the finished volume (up to 1.5× for weaker stone); the calculator starts at 25% for crushed stone, gravel and mix, 12% for sand and 0 for expanded clay and topsoil. Hand-tamped paths often need less. The field is editable — the real figure depends on how hard you compact.
How many square feet does a cubic yard of gravel cover?
One cubic yard is 27 cubic feet, so it covers 324 sq ft at 1 inch, 162 sq ft at 2 inches, 108 sq ft at 3 inches and 81 sq ft at 4 inches deep — before any compaction allowance.
Why does my supplier's tonnage differ from the result?
Bulk density changes with moisture, grading and how the material settles in the truck. Wet sand can be noticeably heavier than dry. Use your supplier's stated density for an exact match.
Which "ton" does the calculator use?
In metric mode, the metric tonne (1000 kg). In US units, the short ton of 2000 lb (907.18474 kg) — not the 2240 lb long ton used historically in Britain.
Why doesn't this calculator do concrete?
Concrete is a mix design problem (cement, sand, aggregate, water, strength class), not a bulk-material quantity. This page covers loose materials only; older saved concrete calculations still open, marked as legacy.
How many tonnes in a cubic metre: bulk density of loose materials
| Material | Bulk density, t/m³ (range) | Tonnes in 1 m³ | Cubic metres in 1 t | Default allowance |
|---|---|---|---|---|
| Crushed stone 5–20 mm | 1.37 (1.36–1.40) | 1.37 | 0.73 | 25 % |
| Crushed stone 20–40 mm | 1.38 (1.33–1.45) | 1.38 | 0.72 | 25 % |
| Crushed stone 40–70 mm | 1.38 (1.37–1.40) | 1.38 | 0.72 | 25 % |
| River sand | 1.50 (1.50–1.60) | 1.50 | 0.67 | 12 % |
| Pit (quarry) sand | 1.50 (1.50–1.60) | 1.50 | 0.67 | 12 % |
| Sand-gravel mix (all-in ballast) | 1.70 (1.60–1.80) | 1.70 | 0.59 | 25 % |
| Expanded clay (LECA) 10–20 mm | 0.45 (0.25–0.60) | 0.45 | 2.22 | 0 % |
| Topsoil | 1.20 (1.10–1.30) | 1.20 | 0.83 | 0 % |
| Gravel | 1.45 (1.40–1.50) | 1.45 | 0.69 | 25 % |
Typical values; the exact density is on your supplier's passport.
Related articles
Part of Home Improvement Calculators